Search results

Thank you very much @CUZOé, I will check the information coming from the ECU. thanks

I understand, but my Golf is a 2015 GTI and I've seen other GTIs with Preh's MIB2 that works perfectly. My Gateway is High and works normally.

Harman MIB 2 and the Performance Monitor is functional, could you send me (post here) the Coding and adapters of the 5F Module, my MIB is unlocked with the FEC and Swaps active, however pressure, temperature do not work, I think it's in the adaptations or coding.

@mr-fix, Hello MR-fix, I wanted to downgrade my firmware version, I want to return from my MHI2_ER_VWG13_K4525 which is installed to the production version MHI2_ER_VWG13_P4521. How can I do this? thanks

Does anyone know if I install a MIB2 (Delphi or Technisat/Preh) with Optical output on a Dynaudio sound system in Golf 7 will it work normally????

I got it, thanks.

I asked this question because I have the Dynaudio system installed on my GOLF GTI MK7 (module, box and sub), and it presented problems with the Harman MIB2 that I have, as I have a MIB2 from Preh (Tecnisat) and one from Delphi, all of them without the optical output, I wanted to replace...

is it possible to connect Dynaudio speakers to a conventional MIB2 media center?

Hi Ricardo, can I help you?

This procedure would be for blind spot calibration, but "apparently" your problem is parameterization! as I suggested, you would update the flash from the master 3C module to version C and parameterize the module referring to version C, done correctly, everything will work correctly. In my case...

ok

You can do it through the VCP, the problem is to find the specific flash file for the VCP. So I think it's easier for you to borrow a VAS5054 and install Odis E on the notebook. If you want, I have the file with the parameters and the flash of the 3C module, but it only works with the...

did you parameterize your master module? I suggest you update the firmware to version C and parameterize the master module. remembering that for firmware update and parameterization you will need VAS 5054 and Odis E.

Good evening everyone, I'm stopping by to share the experience, in solving a problem that occurred in the FLA system. finally everything is working perfect and calibrated. It all started when I was doing the Dynamic calibration of Camera 5Q0, there was a failure and I had to go back home and see...

perfect, that's it!🙌

I did the Installation of cables on the ACC Radar and found no difficulty! Ebcaninei the pair of cables by the side passing through the battery and reaching below the left headlamp! abs.

Good afternoon everyone, today a curious situation happened! I went to test the headlamp with automatic switching, and noticed that it was giving an error on the panel stating a failure in the assist light, I found it strange as it was using the lane assist camera on the 5G0! When I got home I...

I didn't have to go to that point, I thought it would be a waste of time to look for the connector to do this, so I provided a branch splice, and applied a thermo-contracting blanket! It was perfect. in 5 minutes everything was resolved!!!!

Good morning from Brazil @Andrew, observing your situation, I believe you will have success doing what I did in my GTI. 1- You can buy the Canbus extender and it will be the best of all worlds, but in my situation I didn't have the extender at the time, so I used points 13 (Can bus Extended low)...

Boa tarde do Brasil a todos, passando pela caixa de entrada e minhas interações no grupo, percebi que havia uma dúvida nesse tópico, sem uma resposta minha, bom, vamos lá! Tive alguns problemas com meu sistema de park assist, a princípio meu carro não vinha de fábrica com park assist 2.0 (módulo...